Electrical and lighting/UAE

Electrics in a UAE flat: the distribution board and who may touch it

What sits in the board by your front door, what each breaker protects, who may work on it in Dubai, and when a renovation needs the developer, the FM or DEWA.

Librae Academy editorialUpdated

Your flat's electrics start at the distribution board inside the flat, usually in the hallway by the front door. The DEWA meter is not in the flat; it sits in one of the building's electrical rooms, and you never touch it. In a renovation, an electrical contractor enrolled with DEWA works on your board and wiring under the developer's or FM's NOC. DEWA itself comes in only when the load, the board or the incoming supply changes.

This guide covers Dubai, where the Dubai Building Code and DEWA set the rules. Abu Dhabi and Sharjah have their own utilities and rules; ask your contractor which apply.

#What is where

The building's and DEWA's part. The meters belong to DEWA. The cable from the street and the building's main boards belong to DEWA and the building, not to you. In a block of flats the main boards and meters sit in separate electrical rooms, one smart meter per flat. Leave DEWA's equipment alone and report any damage to DEWA.

Your part. A cable runs from the meter to your flat's own board. The Dubai Building Code says:

  • the board is inside your flat, near the entrance;
  • it may not be in a bathroom, bedroom, kitchen, store room, above a sink, in a damp place or under a staircase;
  • its top is no higher than 2 m above the floor, and you can reach it at all times;
  • it is a factory-built board with a main isolator; old rewireable fuses are not allowed;
  • every breaker carries a label saying what it feeds, in English and Arabic.

Supply: 230 V single-phase or 400 V three-phase, 50 Hz. Neutral and earth stay separate everywhere inside the flat.

#What the breakers on your board do

DeviceWhat it doesWhere you meet it
Main isolatorSwitches the whole flat offOne per board, usually at one end of the row
MCB (miniature circuit breaker)Trips on overload or short circuit on one circuitOne per circuit
RCCB, often called ELCB in the UAETrips when current leaks to earth, for example through a person; does not protect against overloadOne device covering a group of circuits
RCBOMCB and RCD in one, for a single circuitInstead of an MCB on circuits that need their own RCD

RCD is the general name for both leakage devices, RCCB and RCBO. Dubai's code recommends these ratings:

CircuitRCD rating
13 A sockets30 mA
Water heater, dishwasher30 mA
Fridge, washing machine30 mA
General lighting30 or 100 mA
Split AC, fan coil100 mA
Electric cooker100 mA

Several circuits can share one RCD, but when it trips, everything behind it goes off. DEWA's inspection list also wants 30 mA protection on cables buried less than 50 mm deep in a wall.

#How circuits are laid out

These are the code's limits. You need them when you add sockets or a new appliance.

  • Lighting: up to 2,000 W per circuit, cable at least 2.5 mm², breaker no bigger than 16 A.
  • Sockets: cable at least 4 mm². A radial circuit takes up to five sockets on a 20 A breaker; a ring takes up to ten on a 30 A breaker. The kitchen may need its own circuits.
  • Each room AC unit: its own circuit, at least 20 A with 4 mm² cable.
  • Water heater and washing machine: each on its own circuit, with a double-pole switch with a neon light. The water heater sits on a 30 mA RCD; if it is in the bathroom, its switch goes outside the door. Details in connecting a water heater.
  • Cooker or hob: its own circuit on a 100 mA RCD, through a cooker control switch within 2 m of the appliance (DEWA's rule). Don't buy a cooker switch with a built-in socket: sockets should stay on their 30 mA RCD.
  • Heights: light switches and the double-pole switches for AC and water heaters at 1.25 m; general sockets at 450 mm; kitchen sockets 150 mm above the worktop.
  • Bathrooms: no switches and no sockets inside, apart from a shaver supply unit. Zones, IP ratings and the rest are in bathroom electrics.

#Who may work on it

Not you, and not a handyman without a licence. Every electrical contractor working in Dubai must enrol with DEWA, which needs a Dubai trade licence for electrical work and engineers with supervision experience. The contractor's engineers supervise the work and test the installation before power goes back on; electrical testing after a renovation covers what they test.

You will see the contractor's licence twice: the developer asks for it with the NOC application, and the FM asks for it before issuing the entry permit. If a company cannot show a trade licence that covers electrical work, don't let it open your board.

#What needs approval during a renovation

The usual case: a flat refit, same board, same supply. You deal with the building, not DEWA.

  1. Swapping fittings and faceplates. Emaar lists electrical fixtures and accessories among works that need no NOC. The contractor still needs an entry permit.
  2. New points, moved sockets and switches, new circuits on the existing board. List every electrical change in the NOC application, with a layout drawing. Emaar bans removing, relocating or covering MEP systems in apartments; whether your moved socket counts is decided in the NOC review, so ask. Dubai Holding communities forbid going over the flat's electrical load. How to apply: the developer NOC.
  3. At completion. Dubai Holding asks for as-built plans of new services. Keep the updated board schedule and the test results; electrical testing after a renovation says what to ask for.

Only if the load, the board or the supply changes. A bigger incoming breaker, a new or larger board, a big new load such as extra AC. DEWA's regulations say no installation may be extended or altered without DEWA's prior approval, and an enrolled contractor files the request for extra load or a modification online. Your flat's load is part of the building's DEWA-approved load schedule, so the building's management has to agree first. You sign; the contractor applies.

Only if the flat is a shell-and-core fit-out, or was handed over without a working connection: you need DEWA's fit-out connection. Only an enrolled contractor or consultant can apply, with the landlord's NOC, a load schedule for your board and wiring layouts. DEWA inspects before it releases the supply.

The grey area. DEWA's rule on alterations is broad. Its public services cover new connections, fit-out connections and extra load, with no separate route for a new circuit on an existing flat board. In practice flat refits run on the NOC alone unless the load or the board changes. Before work starts, ask your contractor to state in writing whether your job needs a DEWA submission. Permits in general: renovation permits in Dubai.

#What goes wrong

  • New appliances on old circuits. An induction hob or oven on a socket circuit trips the breaker or overheats the cable. Big appliances get their own circuit.
  • Everything on one RCD. One leak kills all the sockets at once, often the fridge too.
  • An unlabelled or outdated board. After the renovation nobody knows which breaker feeds what. Labels and a schedule at the board are required.
  • The board boxed in. A wardrobe or false wall in front of it breaks the rule that you can always reach it.
  • Load added without anyone checking. Several new AC units or a hob on a small incomer trip the main breaker in summer. That is exactly when DEWA should have been asked.

#How to check the work

  • The contractor's trade licence covers electrical work and the company is enrolled with DEWA.
  • The NOC application lists every electrical change; the NOC is on site.
  • Sockets, water heater and dishwasher sit behind 30 mA RCDs, and each RCD trips when you press its test button.
  • Every appliance with its own circuit has its own labelled breaker.
  • Labels are in English and Arabic, and the board schedule matches reality.
  • Switches at 1.25 m, sockets at 450 mm, kitchen sockets 150 mm above the worktop.
  • No switch or socket inside the bathroom; the water heater switch is outside.
  • The board is reachable, its top no higher than 2 m.
  • You have the test results for the new circuits and the as-built layout.

#When to call a professional

  • Any work inside the board or on fixed wiring: a DEWA-enrolled electrical contractor.
  • Extra load, a new or larger board, a change at the incoming supply: the same contractor applies to DEWA.
  • Tripping, burning smell, warm breakers: tenants call the landlord or FM; owners call FM or their contractor. Call DEWA only if the whole floor is dark or the meter side is damaged.

Draw the socket and lighting plan in Librae. Once the electrician agrees it, it is issued "For works" with a number, and that is the plan they wire to. In the UAE, with independent quality control added to a renovation ordered through Librae, a specialist checks the first-fix wiring before the walls are closed.

#What the codes say

Part G of the Dubai Building Code 2021 is now Dubai's design rulebook for electrics: in January 2022 DEWA moved its design clauses into it and checks drawings against it. DEWA's Regulations for Electrical Installations, 2017 edition, still govern operation, periodic inspection and maintenance, including the no-alterations-without-approval rule. Both are based on the British wiring regulations, BS 7671. The RCD ratings in the code's table are recommendations; the designer confirms them with the manufacturer. Developer rules, such as Emaar's fact sheet and Dubai Holding's community rules, add the building's own conditions.

This guide explains good practice and cites the documents listed below. It is not a permit, a design approval or an engineering opinion. Work on electrical, gas, fire-safety and structural elements must be carried out by licensed professionals and approved by the relevant authority.

Sources

  1. Dubai Building Code 2021, Part G, sections G.4.1–G.4.5 (supply, metering), pp. 418–424 — 230/400 V supply, meters in separate switchrooms, one smart meter per consumer, consumer protects DEWA equipment.
  2. Dubai Building Code 2021, Part G, G.4.7.2, G.4.12.2, G.4.13.5–G.4.13.8, G.4.16.1 (pp. 428–447) — Conductor sizes, factory-built boards with isolator, no rewireable fuses, cooker, water heater and AC circuits, lighting and socket circuit limits.
  3. Dubai Building Code 2021, Part G, G.4.18.2, G.4.18.4–G.4.18.6, G.4.19.1, G.4.19.4 Table G.21 (pp. 458–465) — Where the board may go and its height, labels, mounting heights, no switches or sockets in bathrooms, TN-S, recommended RCD ratings.
  4. DEWA, Regulations for Electrical Installations, 2017 Edition, sections 1.4–1.7, 1.12, 1.14, 4.6.3 — Contractor enrolment, prior approval for new or additional work, inspection checklist, no alterations without DEWA approval, cooker switch within 2 m.
  5. DEWA circular DP-VP-CS-GEN-0008-2022 (17 January 2022), Dubai Building Code incorporating DEWA regulations — Design clauses moved into the Dubai Building Code; the 2017 regulations still govern operation, periodic inspection and maintenance.
  6. DEWA service guide, Getting Electricity Fit-Out Connections — Only enrolled contractors and consultants apply; landlord NOC, the main project's DEWA-approved load schedule, a load schedule for the flat's board and wiring layouts; DEWA LV inspection.
  7. DEWA service guide, Getting Electricity Connections — Enrolled consultants and contractors only; the same route is used for additional load; LV design approval and LV inspection.
  8. DEWA service guide, Enrollment of Consultants and Contractors — Electrical contractor enrolment needs a trade licence and at least one year of supervision experience.
  9. Emaar Community Management, Home modifications fact sheet (2022) — Electrical fixtures and accessories need no NOC but contractors need an entry permit; apartments may not remove, relocate or cover MEP systems.
  10. Dubai Holding Community Management, Community Rules and Regulations (01 Oct 2026), sections 8.1.17 and 8.1.40 — Electrical load may not be exceeded; as-built plans of new services handed over at completion.

Читать по-русски